EMI4192MTTAG
two-pair common-mode filter with integrated ESD protection for high-speed differential interfaces
Key details
| Part Number | EMI4192MTTAG |
|---|---|
| Manufacturer | onsemi |
| Category | Common Mode Filter |
| Lifecycle Status | Production |
| Series | EMI4192 |
| Package / Case | 10-pin WDFN, 2.0 mm × 2.5 mm |
| Pin Count | 10 |
| Operating Temperature | -40°C to +85°C |
| Last Verified | 2026-07-20 |
Part information
EMI4192MTTAG Overview
EMI4192MTTAG is a onsemi two-pair common-mode filter with integrated ESD protection for high-speed differential interfaces supplied in 10-pin WDFN, 2.0 mm × 2.5 mm. This page uses the exact orderable code because package, grade, temperature and option suffixes can change compatibility.
Key Technical Specifications
| Differential Pairs | 2 |
|---|---|
| Differential Bandwidth | Greater than 2 GHz |
| ESD Contact Rating | ±15 kV IEC 61000-4-2 |
| Function | Common-mode noise filtering and ESD protection |
| Packing | Tape and reel |
Package and Ordering Notes
The listed package is 10-pin WDFN, 2.0 mm × 2.5 mm with 10 pins, leads, lands or contacts. The featured image is a generic package illustration for form-factor identification and is not an actual date-code or lot photograph. The part or family is listed by onsemi as Production at the verification date.
Sourcing Guidance
Confirm current factory lead time, packing format and revision for EMI4192MTTAG before placing the order.
For an accurate quotation, include the full MPN, target quantity, acceptable date-code range, packaging format and destination. Icearth can help review traceability documents, label photos and electrical/package alignment before order placement.
Manufacturer Documentation
Technical values were checked against onsemi documentation. Use the linked datasheet as the controlling source and re-check revisions before PCB release or firmware qualification.
EMI4192MTTAG selection and design context
EMI4192MTTAG is cataloged as a Common Mode Filter in the EMI4192 family. Its recorded function is two-pair common-mode filter with integrated ESD protection for high-speed differential interfaces. Selection should be based on the complete electrical limits, package drawing and ordering suffix rather than the abbreviated family code.
- Differential Pairs: 2. Confirm the value and its datasheet test conditions for the exact ordering suffix.
- Differential Bandwidth: Greater than 2 GHz. Confirm the value and its datasheet test conditions for the exact ordering suffix.
- ESD Contact Rating: ±15 kV IEC 61000-4-2. Confirm the value and its datasheet test conditions for the exact ordering suffix.
- Function: Common-mode noise filtering and ESD protection. Confirm the value and its datasheet test conditions for the exact ordering suffix.
Application and qualification considerations
When evaluating this protection device, confirm working voltage, clamping behavior, surge or ESD rating, capacitance, polarity and placement relative to the protected interface. For a new design, review power-up behavior, interface timing, absolute maximum ratings, thermal limits and any external-component requirements in the latest manufacturer documentation. Existing-board replacement work should additionally confirm pinout, footprint, firmware assumptions and qualification grade.
Procurement checks for EMI4192MTTAG
The recorded package is 10-pin WDFN, 2.0 mm × 2.5 mm, the temperature range is -40°C to +85°C, and the lifecycle status is Production as of 2026-07-20. Before ordering, confirm the exact MPN on the label, packing format, quantity, date-code requirements, traceability documents and current factory status.
EMI4192MTTAG FAQ
What distinguishes EMI4192MTTAG within the EMI4192 family?
EMI4192MTTAG is the exact orderable code for a two-pair common-mode filter with integrated ESD protection for high-speed differential interfaces in 10-pin WDFN, 2.0 mm × 2.5 mm. Related EMI4192 devices may change package, rating, interface option or qualification grade, so compare the manufacturer ordering table before substitution.
What package and footprint checks are required for EMI4192MTTAG?
EMI4192MTTAG is recorded in 10-pin WDFN, 2.0 mm × 2.5 mm with 10 pins, leads or contacts. Confirm the manufacturer package drawing, dimensions, pin numbering, exposed-pad requirements and packing suffix before releasing a PCB footprint.
Which specifications should be verified when selecting EMI4192MTTAG?
Differential Pairs is recorded as 2, Differential Bandwidth is recorded as Greater than 2 GHz. Use the latest datasheet for minimum and maximum limits, test conditions, timing and absolute maximum ratings rather than relying only on a distributor summary.
What is the lifecycle status of EMI4192MTTAG?
EMI4192MTTAG was recorded as Production when verified on 2026-07-20. Reconfirm factory status, revision availability, lead time and any last-time-buy notice before design-in or volume procurement.
What information should be included in an RFQ for EMI4192MTTAG?
Provide the complete EMI4192MTTAG orderable code, target quantity, acceptable date-code range, required packing method, delivery destination and documentation needs. For replacement work, also identify the existing package and any mandatory qualification grade.
Lifecycle and sourcing review
Lifecycle information is shown for reference. Confirm current manufacturer documentation, availability and technical suitability before purchase.
Confirm current factory lead time, packing format and revision for EMI4192MTTAG before placing the order.